|
Air Filter - 41.5cc eton, cobra, rock
|
|
Axle - Rear Drive Assembly, Cobra
|
|
Belt Cover - Rock
|
|
|
|
|
|
|
|
|
Stock air filter for 41.5cc 2-stroke E-ton, Cobra, and The Rock gas scooters.
|
Rear drive axle assembly for the Rock and Cobra gas scooters.
|
Chrome belt cover for Cobra, and The Rock gas scooters.
Specifications:
Width: 5 1/8 inches
Length: 10 7/8 inches
Thickness: 7/8 inch
|
|
|
|
Carburetor - Stock, Rock
|
|
Carburetor Kit - Stock, Rock (replaces the original carburetor)
|
|
Clutch - Cobra, Rock (Eton 42cc)
|
|
|
|
|
|
|
|
|
Stock carburetor for the 41.5cc 2-stroke E-ton, Cobra, and The Rock gas scooters.
|
This carburetor kit replaces the original stock carburetor on The Rock and Cobra scooters and the 41.5cc Eton 2 cycle engine. Shop tested and works just as good or better then the original.
|
Stock clutch for the 41.5cc 2-stroke E-ton, Cobra, and The Rock gas scooters.
NOW BACK IN STOCK!
|
|
|
|
Clutch Housing - Rock
|
|
Crank Case - Cover, Rock
|
|
Crank Case - Right Side, Rock
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Drive shaft & Pulley Assembly
|
|
Engine Mounts, Rock
|
|
Exhaust - Rock, Cobra
|
|
|
|
|
|
|
|
Upper drive shaft with pulley assembly.
Specifications:
Shaft
Length: 190mm
Pulley
Diameter: 31mm
Notes: We came across a few used drive shafts with pulleys assembly's. They are in used but working condition. Also the pulley gear as been spot welded to the shaft for extra strength. We only have 6 and they won't last long and once sold out we won't be able to restock anymore...
|
Engine mount kit for for the Cobra, and The Rock gas scooters.
BACK IN STOCK!!
|
Replacement exhaust pipe for the Cobra, and The Rock gas scooters.
BACK IN STOCK!!
|
|
|
|
Gas Tank - Low Rider Rock
|
|
Ignition Coil (One Prong) - 22/26cc, 2-cycle
|
|
Mud Flap - Rock
|
|
|
|
|
|
|
|
Fits the Rock, Cobra, Razer and Grizzly gas scooters. As well as other models with the same style gas tank.
Specifications:
Width: 11.4 cm / 4.5 inches
Length: 34.2 cm / 13.5 inches
Thickness: 2 inches
|
Ignition coil for 22cc & 26cc 2-cycle engine.
Specifications:
Bolt Hole Spacing: 35mm or 1.30 inches (center to center)
Wires: 2 wires, 1 black and 1 Red
|
Rear mud flap for the Cobra, and The Rock gas scooters.
|
|
|
|
Neck, Folding Assy
|
|
Pull Start, Gen I & III - Rock (E-ton engine)
|
|
Rim - Aluminum Rock Rear -Black
|
|
|
|
|
|
|
|
Lower goose neck assembly for The Rock and Cobra scooters.
Comes as shown in picture.
|
Pull starter for the 415cc Eton engine, Cobra, and The Rock gas scooters.
Note: Please check the inside of your pull start to confirm that you order the correct item.
Specifications:
Center portion of the part that silver: 45mm/ 1.77 inches
Bolt hole to bolt hole: 71mm/ 2.79 inches
Thickness: 1 5/8 inch
|
Aluminum Rear Rim for the Rock, Cobra and other models that use the same style rim.
Specifications:
Hardware included
|
|
|
|
Tire - 9x3.50-4
|
|
|
|
|
|
|
|
|
|
|
|
Become a Fan
Follow Us
Watch Our Channel