|
Air Filter - 41.5cc eton, cobra, rock
|
|
Axle - Rear Drive Assembly, Cobra
|
|
Belt Cover - Rock
|
|
|
|
|
|
|
|
|
Stock air filter for 41.5cc 2-stroke E-ton, Cobra, and The Rock gas scooters.
|
Rear drive axle assembly for the Rock and Cobra gas scooters.
|
Chrome belt cover for Cobra, and The Rock gas scooters.
Specifications: Width: 5 1/8 inches Length: 10 7/8 inches Thickness: 7/8 inch
|
|
|
Carburetor - Stock, Rock
|
|
Carburetor Kit - Stock, Rock (replaces the original carburetor)
|
|
Carburetor Kit HP for The Rock, Cobra and Eton 41.5cc (Sauser air filter version)
|
|
|
|
|
|
|
|
|
Stock carburetor for the 41.5cc 2-stroke E-ton, Cobra, and The Rock gas scooters.
|
This carburetor kit replaces the original stock carburetor on The Rock and Cobra scooters and the 41.5cc Eton 2 cycle engine. Shop tested and works just as good or better then the original.
|
This carburetor kit replaces the original stock carburetor on The Rock,
Cobra, Razer and all scooters that use the 41.5cc Eton 2 cycle engine. Shop tested and works great!.
Kit includes the fully adjustable high performance Walbro style carburetor with air and fuel mixture adjustments, the high performance air filter and velocity stack. Kit will improve throttle response, acceleration and top end as well as keep your engine running cleaner.
Description:
15.5mm HP Carburetor W/ high & low adjustments
Saucer Air Filter
Velocity Stack
Built in choke
Vacuum Adapter Plate Fuel Line
Note: You will also have to remove the metal plate below the stock carburetor in order for the replacement version to fit.
|
|
|
Carburetor Kit HP for The Rock, Cobra and Eton 41.5cc (Straight air filter version)
|
|
Clutch - Cobra, Rock (Eton 42cc)
|
|
Clutch Housing - Rock
|
|
|
|
|
|
|
|
Kit includes the fully adjustable high performance Walbro style carburetor with air and fuel mixture adjustments, the high performance air filter and velocity stack. This kit will improve throttle response, acceleration and top end as well as keep your engine running cleaner.
Description: 15.5mm HP Carburetor W/ high & low adjustments Straight Air Filter Velocity Stack Built in choke Vacuum Adapter Plate
Carburetor Kit Fits the 41.5cc 2-stroke E-ton, Cobra, and The Rock gas scooters.
|
Stock clutch for the 41.5cc 2-stroke E-ton, Cobra, and The Rock gas scooters.
NOW BACK IN STOCK!
|
|
|
|
Crank Case - Cover, Rock
|
|
Crank Case - Right Side, Rock
|
|
Drive shaft & Pulley Assembly
|
|
|
|
|
|
|
|
|
|
|
Upper drive shaft with pulley assembly.
Specifications: Shaft Length: 190mm Pulley Diameter: 31mm
Notes: We came across a few used drive shafts with pulleys assembly's. They are in used but working condition. Also the pulley gear as been spot welded to the shaft for extra strength. We only have 6 and they won't last long and once sold out we won't be able to restock anymore...
|
|
|
Engine Mounts, Rock
|
|
Exhaust - Rock, Cobra
|
|
Forks - Rock
|
|
|
|
|
|
|
|
Engine mount kit for for the Cobra, and The Rock gas scooters.
BACK IN STOCK!!
|
Replacement exhaust pipe for the Cobra, and The Rock gas scooters.
BACK IN STOCK!!
|
Stock front forks for the Cobra, and The Rock gas scooters.
BACK IN STOCK !!
|
|
|
Gas Tank - Low Rider Rock
|
|
Ignition Coil (One Prong) - 22/26cc, 2-cycle
|
|
Mud Flap - Rock
|
|
|
|
|
|
|
|
Fits the Rock, Cobra, Razer and Grizzly gas scooters. As well as other models with the same style gas tank.
Specifications: Width: 11.4 cm / 4.5 inches Length: 34.2 cm / 13.5 inches Thickness: 2 inches
|
Ignition coil for 22cc & 26cc 2-cycle engine.
Specifications: Bolt Hole Spacing: 35mm or 1.30 inches (center to center) Wires: 2 wires, 1 black and 1 Red
|
Rear mud flap for the Cobra, and The Rock gas scooters.
|
|
|
Neck, Folding Assy
|
|
Pull Start, Gen I & III - Rock (E-ton engine)
|
|
Tire - 9x3.50-4
|
|
|
|
|
|
|
|
Lower goose neck assembly for The Rock and Cobra scooters.
Comes as shown in picture.
|
Pull starter for the 415cc Eton engine, Cobra, and The Rock gas scooters.
Note: Please check the inside of your pull start to confirm that you order the correct item.
Specifications: Center portion of the part that silver: 45mm/ 1.77 inches Bolt hole to bolt hole: 71mm/ 2.79 inches Thickness: 1 5/8 inch
|
|
|